Hinges and concealed hinges are the key to a piece of furniture. Because the hinges are switched more than 10 times a day on average in a person's life, a hinge is good or bad depending on whether you are good or bad, and the hinge hardware in the selection also needs a meaning. Basically, the hinge can be distinguished from the following aspects.
1, the surface: look at the surface of the product is smooth, if you see the shape, it is produced with scrap (edge ​​material), this kind of hinge ugly appearance, so that your furniture is no grade. Surface: Most of the hinges are nickel-plated. Now, because of the low cost, only a thin layer of nickel-plated hinges should be plated with a layer of acid copper before the nickel layer. This can prevent rust. Tips: Teach: Everyone has a way to tell if there is any way: if js does not oppose the situation, you can use artistic power to draw a knife. Look at whether you can see the yellow copper layer. There is a more method that is to look inside the hinged cup, which is generally hinged, and here is also In places where plating is most difficult, black water is seen in the cup or iron is seen, which proves that the electroplating layer is thin and does not pass. When the brightness of the cup is close to other parts, the clearance is passed. Isn't it simple?
2. The switch performance knows that the hinge key is a function, so this is very important. Guan Jian takes the outer spring and the inner spring of the hinge, and the rivet assembly spring is the spring piece. The inner spring is the spring bar and must pass through. A certain amount of heat, too hard to break easily, too soft to close the door, some js purchase low-priced spring accessories, resulting in not closing well or the spring breaking off the door panel. Tips: When buying a hinge (except for a hydraulic hinge), manually closing the hinge and listening to the sound of the hinge closing, is it crisp? Clear mediation is boring and proves that the spring force is not enough and there is a problem with the thickness of the material. Is it loose? There is loose evidence that rivets are not tightly riveted and are easily detached. It is not obvious that the indentation in the cup is obvious when it is closed several times, which proves that the thickness of the cup is problematic and easy."
3, screws: general hinge comes with two screws, are adjusted before and after the tone up and down some new hinges are also brought around in the so-called three-dimensional adjustment hinge, usually with two adjustment stations enough. The small silk knife adjusts the screw up and down three or four times with the point strength, and then the screw, to see if the teeth of the hinge arm are damaged, a hinge arm is formed of iron material, without the screw so hard, capacity, also There are cases where the accuracy of tapping the factory is not enough, it is easy to slip the wire, or screw the situation. Front and rear adjustment screws are also some tests.
1, the surface: look at the surface of the product is smooth, if you see the shape, it is produced with scrap (edge ​​material), this kind of hinge ugly appearance, so that your furniture is no grade. Surface: Most of the hinges are nickel-plated. Now, because of the low cost, only a thin layer of nickel-plated hinges should be plated with a layer of acid copper before the nickel layer. This can prevent rust. Tips: Teach: Everyone has a way to tell if there is any way: if js does not oppose the situation, you can use artistic power to draw a knife. Look at whether you can see the yellow copper layer. There is a more method that is to look inside the hinged cup, which is generally hinged, and here is also In places where plating is most difficult, black water is seen in the cup or iron is seen, which proves that the electroplating layer is thin and does not pass. When the brightness of the cup is close to other parts, the clearance is passed. Isn't it simple?
2. The switch performance knows that the hinge key is a function, so this is very important. Guan Jian takes the outer spring and the inner spring of the hinge, and the rivet assembly spring is the spring piece. The inner spring is the spring bar and must pass through. A certain amount of heat, too hard to break easily, too soft to close the door, some js purchase low-priced spring accessories, resulting in not closing well or the spring breaking off the door panel. Tips: When buying a hinge (except for a hydraulic hinge), manually closing the hinge and listening to the sound of the hinge closing, is it crisp? Clear mediation is boring and proves that the spring force is not enough and there is a problem with the thickness of the material. Is it loose? There is loose evidence that rivets are not tightly riveted and are easily detached. It is not obvious that the indentation in the cup is obvious when it is closed several times, which proves that the thickness of the cup is problematic and easy."
3, screws: general hinge comes with two screws, are adjusted before and after the tone up and down some new hinges are also brought around in the so-called three-dimensional adjustment hinge, usually with two adjustment stations enough. The small silk knife adjusts the screw up and down three or four times with the point strength, and then the screw, to see if the teeth of the hinge arm are damaged, a hinge arm is formed of iron material, without the screw so hard, capacity, also There are cases where the accuracy of tapping the factory is not enough, it is easy to slip the wire, or screw the situation. Front and rear adjustment screws are also some tests.
Emergency Battery Pack,Emergency Lighting Battery Pack,Emergency Battery Pack For Led Lights,Led Emergency Battery Pack
NINGBO JIMING ELECTRIC APPLIANCE CO., LTD. , https://www.feituosafety.com