As the name implies, the difference between the thickness and the thickness of the sheet that is used to fasten the two items for fastening is called the main difference between the buckle and the tensile force. The standard of the buckle is between 1.5 and 3.0. Less than 1.2 is non-standard and may cause security problems.
The general standard can refer to the following list:
Buckle for car: The material is required to be calcined at a high temperature and the thickness is between 3mm and 5mm.
Vibrating device type buckle: Requires elastic, adjustable, thickness between 3mm-2mm.
Outdoor wet buckle: 304 stainless steel is required to be corrosion resistant. The thickness is between 1.5 and 2.5.
Judging quality editing starts with the surface treatment of the product: the product made from the good plate has a smooth surface and the plating is smooth. The products made from poor plates are pitted, even if several layers are plated, because plating does not fill the surface defects of the product. Some will also have problems such as small bubbles or yellowing. These are the performances of the defective products.
Starting from the edge and inside of the product: good products are produced through burrs, so that the products will not be scratched or ugly; even the products that have been used for a long time will produce burrs, so they must be processed; Poor products are produced and assembled directly without surface treatment. This saves a part of the cost, and it will be scratched or difficult to open when used. This is called cutting corners.
Starting from the thickness of the product material: people often see that the good product material is thick, used for a long time, the poor product is thin and cheap, and it will take a long time to break. The same reason is the same. The good product material is thick, the force is strong, the number of uses is long, and the life is long. The poor product material is weak under the force of the material, so that the deformation is easy to damage, the number of uses is small, and the life is short.
Starting from the assembly technology of each product: the product is good or bad, the life is long and short, and the assembly technology has a lot to do with the assembled parts. A good product is assembled and the details of each activity are quite flexible. The rivets and springs are made according to the size standard of the product. Poor products are either too tightly packed or too loose, the gaps are too large to shake up and down, and the rivets and springs are non-standard, which can degrade the quality and life of the product.
Starting from the intrinsic quality of the product: good products do not require fancy external packaging. Good packaging that is not durable is a common means used by many manufacturers to deceive consumers. It is a really good product to stand the test of time.
Material classification editing main points: stainless steel, iron, copper, zinc alloy, plastic rubber...
The main categories of buckle classification editing: stainless steel flat mouth buckle, heavy military buckle, long buckle, spring buckle, adjustment buckle, compartment buckle, bridge buckle, luggage buckle, self-locking buckle application range edit stainless steel Flat mouth buckle stainless steel flat mouth buckle market is known as stainless steel buckle. It is assembled from 304 stainless steel sheets and assembled through several procedures. Mainly used in stainless steel products industry, instrument industry, electromechanical equipment industry, packaging industry, high-tech industry, logistics industry...
Flat mouth buckle flat mouth buckle stainless steel flat mouth buckle mainly divided into four specifications: heavy flat mouth buckle 79mm, thickness: 1.8mm; No. 1 flat mouth buckle 90mm, thickness: 1.5mm; No. 2 flat mouth Buckle 73mm, thickness: 1.5mm; No. 3 flat mouth buckle 57mm, thickness: 1.2mm.
Different forms of buckles in different forms (4 photos)
Heavy military buckles, as the name suggests, are mainly fasteners on military product packaging boxes for military and logistics product packaging. There are also many industries in the industry that use such fasteners, such as: import and export boxes, transport boxes, air boxes, and so on. There are two types of heavy military buckles: the large standard load-bearing capacity is: 95KG, the small standard load is 70KG.
The compartment buckle is used as a fastener for the rear compartment of a car, a freight car or an electric tricycle.
The insurance buckle is mainly based on the buckle to add a piece of insurance, so that the buckle is not opened or bounced freely. Therefore, the insurance buckle can play a safe role. It is used for mechanical vibration or frequent collision to protect.
Adjustable buckle
1) It is used in high-end machines and precision equipment to adjust the precision.
2) It can adjust the installation position during use, which is suitable for operation and is more conducive to operation. It is commonly used in heavy-duty buckles.
3) Adjustable plastic buckle.
It is a plastic accessory used for the back of the hat. It is made of polyethylene and molded by injection molding.
The general standard can refer to the following list:
Buckle for car: The material is required to be calcined at a high temperature and the thickness is between 3mm and 5mm.
Vibrating device type buckle: Requires elastic, adjustable, thickness between 3mm-2mm.
Outdoor wet buckle: 304 stainless steel is required to be corrosion resistant. The thickness is between 1.5 and 2.5.
Judging quality editing starts with the surface treatment of the product: the product made from the good plate has a smooth surface and the plating is smooth. The products made from poor plates are pitted, even if several layers are plated, because plating does not fill the surface defects of the product. Some will also have problems such as small bubbles or yellowing. These are the performances of the defective products.
Starting from the edge and inside of the product: good products are produced through burrs, so that the products will not be scratched or ugly; even the products that have been used for a long time will produce burrs, so they must be processed; Poor products are produced and assembled directly without surface treatment. This saves a part of the cost, and it will be scratched or difficult to open when used. This is called cutting corners.
Starting from the thickness of the product material: people often see that the good product material is thick, used for a long time, the poor product is thin and cheap, and it will take a long time to break. The same reason is the same. The good product material is thick, the force is strong, the number of uses is long, and the life is long. The poor product material is weak under the force of the material, so that the deformation is easy to damage, the number of uses is small, and the life is short.
Starting from the assembly technology of each product: the product is good or bad, the life is long and short, and the assembly technology has a lot to do with the assembled parts. A good product is assembled and the details of each activity are quite flexible. The rivets and springs are made according to the size standard of the product. Poor products are either too tightly packed or too loose, the gaps are too large to shake up and down, and the rivets and springs are non-standard, which can degrade the quality and life of the product.
Starting from the intrinsic quality of the product: good products do not require fancy external packaging. Good packaging that is not durable is a common means used by many manufacturers to deceive consumers. It is a really good product to stand the test of time.
Material classification editing main points: stainless steel, iron, copper, zinc alloy, plastic rubber...
The main categories of buckle classification editing: stainless steel flat mouth buckle, heavy military buckle, long buckle, spring buckle, adjustment buckle, compartment buckle, bridge buckle, luggage buckle, self-locking buckle application range edit stainless steel Flat mouth buckle stainless steel flat mouth buckle market is known as stainless steel buckle. It is assembled from 304 stainless steel sheets and assembled through several procedures. Mainly used in stainless steel products industry, instrument industry, electromechanical equipment industry, packaging industry, high-tech industry, logistics industry...
Flat mouth buckle flat mouth buckle stainless steel flat mouth buckle mainly divided into four specifications: heavy flat mouth buckle 79mm, thickness: 1.8mm; No. 1 flat mouth buckle 90mm, thickness: 1.5mm; No. 2 flat mouth Buckle 73mm, thickness: 1.5mm; No. 3 flat mouth buckle 57mm, thickness: 1.2mm.
Different forms of buckles in different forms (4 photos)
Heavy military buckles, as the name suggests, are mainly fasteners on military product packaging boxes for military and logistics product packaging. There are also many industries in the industry that use such fasteners, such as: import and export boxes, transport boxes, air boxes, and so on. There are two types of heavy military buckles: the large standard load-bearing capacity is: 95KG, the small standard load is 70KG.
The compartment buckle is used as a fastener for the rear compartment of a car, a freight car or an electric tricycle.
The insurance buckle is mainly based on the buckle to add a piece of insurance, so that the buckle is not opened or bounced freely. Therefore, the insurance buckle can play a safe role. It is used for mechanical vibration or frequent collision to protect.
Adjustable buckle
1) It is used in high-end machines and precision equipment to adjust the precision.
2) It can adjust the installation position during use, which is suitable for operation and is more conducive to operation. It is commonly used in heavy-duty buckles.
3) Adjustable plastic buckle.
It is a plastic accessory used for the back of the hat. It is made of polyethylene and molded by injection molding.
kaiping aida sanitary ware technology co.,ltd , https://www.kpaidafaucets-jm.com