The decoration of the bathroom must not be neglected. The installation of the corresponding sanitary ware especially requires us to be cautious. For sanitary ware, it is indispensable in our daily life. The installation of sanitary ware not only affects the aesthetics of our decoration, but also affects the comfort we use. The following small series will give a detailed introduction to the installation of sanitary ware.
Installation of sanitary ware: installation of the bathtub 1. Test the water to see if there is any leakage: Before we put the bathtub, we need to install the corresponding water fittings, and we need to do the water shut for 24 hours, then look at it. Look at the leaking water in the bathtub, especially pay attention to the overflow.
Second, the bathtub leveling: When we are laying the bathtub, we must pay attention to the corresponding water outlet is lower than the inlet end, so as to avoid the poor discharge. The corresponding bathtub should not only be visually level, but also pay attention to not affect the drainage. Third, sand filling: relative to the cast iron bathtub
In fact, it is strong but the thermal conductivity is very fast, so it is necessary to use the Zhonghe sand for bottoming. Of course, foam can also be used because the foam does not have fluidity. It is also necessary to pay attention to the fact that the sand cannot leak into the downpipe when filling the river sand.
Fourth, the inspection and repair: we also need to pay attention to the location of the water in the water outlet 300mm wide and 400mm holes, according to the size of the waterproof and anti-corrosion treatment. The purpose of this is to have a good mouth in the future when we are doing maintenance. Installation of sanitary ware: installation of washbasin 1. Installation of washbasin: When we install the washbasin of the pipe rack, we must first draw the line of the lower water pipe, then measure the height of the ground upwards, and on the wall Be sure to draw a horizontal line. Mark the mark according to the width of the washbasin, and then make a 120 mm deep hole. Clean up the relevant debris and keep the installation parts clean. Second, cast iron frame
Installation of the washbasin: As with the above installation, it is also necessary to mark the center of the lower water pipe, then measure the height, and draw a horizontal line to form a crosshair. According to the width of the washbasin and then mark on the center line, and the pot holder is placed, the position of the screw hole is reserved, and the size needs to be marked.
Installation of sanitary ware: Installation of toilet bowl 1. Take out the pipe plug of the ground drain, and then check if there are any debris in the pipe. If necessary, clean the corresponding debris. Then clean the circumference of the nozzle, and then connect the corresponding outlet of the toilet to the lower water outlet to make it level and correct. Then we need to mark the bolt holes in the toilet.
Second, punch holes. Corresponding holes of 20 mm in diameter and 60 mm in depth are required at the corresponding stamps. Then insert the bolt into the hole, then use cement to secure it and align the toilet eye with the bolt. Then, the putty is applied around the corresponding water outlet of the toilet and the lower water pipe mouth, and the corresponding four bolt holes of the toilet are screwed until the tightness is moderate.
Third, install the rear end of the toilet bowl. It should be installed according to the corresponding drawings or the lined part, and the relevant bolts need to be fixed. The degree of fixing needs to be moderate and not too tight.
Fourth, install the back water tank. When installing the water tank, we need to pay attention to the moderate size, not too loose or too tight.
Fifth, pick up the water. The installation of the water supply system also needs attention, and it is impossible to leak water. Pay attention to the tightness of the tightness when you receive the water.
When installing sanitary ware, we also need to pay attention to check the relevant water leakage. The above is the installation procedure for the sanitary ware that Xiaobian explained for everyone today. I believe everyone knows it. I hope this article can help you.
Multi-purpose shelves, shelves, items that can be placed, and decorative walls..
Functional wooden wall shelf, simple and practical, personalized decoration, multi-purpose storage.
Features natural wood, corrosion-resistant, does not contain any harmful substances, and is durable..
Iron pipe support, sturdy and durable, unique style, simple and generous..
Wrought iron pipes, thick pipes, thickened walls, seamless splicing, high-temperature paint treatment, combined with solid wood laminates, more stable and durable.
DIY Water Pipe Paper Towel Holder
Pipe Paper Towel Holder,Industrial Pipe Paper Towel Holder,Pipe Towel Holder,Diy Water Pipe Paper Towel Holder
Foshan Nanhai Xin Jianwei Hardware Co., Ltd , https://www.aaghardware.com