1. The mixer should be installed on a solid flat surface to prevent dumping due to ground subsidence.
2. Before using the work, check the various systems of the machine according to the procedures of cleaning, fastening, lubricating, adjusting and anti-corrosion, and make them meet the requirements; hidden accidents must be promptly eliminated.
3, electric driven mixers, distribution equipment should be installed appropriate fuses and grounding devices to ensure the safety of electrical systems.
4. During the operation of the mixer, do not allow the gravel to fall into the running part of the machine to prevent the parts from being stuck and being damaged.
5. After the hopper is lifted up, no one is allowed to pass or stay under the hopper. If it is necessary to perform maintenance under the bucket, shut down the power and shut down the hopper with a chain of insurance. Feed hopper should be slowly put down, so as not to fall too fast, damage the parts or failure.
6, before the discharge can not be without reason to stop, but can not start after feeding, the amount can not exceed the specified capacity.
7. Feeding shall not be carried out until the hopper has not stopped.
8, the mixer body must be installed firmly and firmly. Before the work, check whether the clutch and brake are flexible and reliable, whether the wire rope is broken, whether the protection device is complete and reliable, and perform trial operation; if the mixing drum rotates smoothly, does not jump, does not run, the hopper moves up and down and the material discharging door rotates flexibly. The hopper under the cam mechanism is normal for work. It is forbidden to use overloaded equipment. It is forbidden to use hands or other objects to penetrate into the mixing drum to perform operations such as fingering, cleaning and repair.
9. When the mixer suddenly runs out of power or fails during full-load operation, apply the manpower to clear the mixing cartridge's memory material, and then check or repair it. It is not allowed to start the mixer at full load in case of excessive current during starting and damage the motor.
10. If the operator must enter the mixing drum for cleaning or maintenance, the power supply should be strictly controlled to prevent accidents.
11. After the mixing work is completed, the mixer must be cleaned in time to prevent the concrete from agglomerating. When cleaning, prevent electrical equipment from getting wet. Cleaning must be performed after power off to prevent electric shock
2. Before using the work, check the various systems of the machine according to the procedures of cleaning, fastening, lubricating, adjusting and anti-corrosion, and make them meet the requirements; hidden accidents must be promptly eliminated.
3, electric driven mixers, distribution equipment should be installed appropriate fuses and grounding devices to ensure the safety of electrical systems.
4. During the operation of the mixer, do not allow the gravel to fall into the running part of the machine to prevent the parts from being stuck and being damaged.
5. After the hopper is lifted up, no one is allowed to pass or stay under the hopper. If it is necessary to perform maintenance under the bucket, shut down the power and shut down the hopper with a chain of insurance. Feed hopper should be slowly put down, so as not to fall too fast, damage the parts or failure.
6, before the discharge can not be without reason to stop, but can not start after feeding, the amount can not exceed the specified capacity.
7. Feeding shall not be carried out until the hopper has not stopped.
8, the mixer body must be installed firmly and firmly. Before the work, check whether the clutch and brake are flexible and reliable, whether the wire rope is broken, whether the protection device is complete and reliable, and perform trial operation; if the mixing drum rotates smoothly, does not jump, does not run, the hopper moves up and down and the material discharging door rotates flexibly. The hopper under the cam mechanism is normal for work. It is forbidden to use overloaded equipment. It is forbidden to use hands or other objects to penetrate into the mixing drum to perform operations such as fingering, cleaning and repair.
9. When the mixer suddenly runs out of power or fails during full-load operation, apply the manpower to clear the mixing cartridge's memory material, and then check or repair it. It is not allowed to start the mixer at full load in case of excessive current during starting and damage the motor.
10. If the operator must enter the mixing drum for cleaning or maintenance, the power supply should be strictly controlled to prevent accidents.
11. After the mixing work is completed, the mixer must be cleaned in time to prevent the concrete from agglomerating. When cleaning, prevent electrical equipment from getting wet. Cleaning must be performed after power off to prevent electric shock
ShaoXing Change Auto Synchronizer Ring Co.,Ltd , https://www.sxcjautoparts.com