Home>Bearing knowledge>Application of self-smooth bearings in casting |
Self-smooth bearing in casting
/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
The aluminum liquid produced by the aluminum electrolytic cell is sucked out by vacuum lifting and poured into the mixing furnace; after being proportioned and slag removed; flowing into the aluminum ingot casting machine for casting; the solid formed is called aluminum ingot; The aluminum ingot is stacked by the stacker. In order to improve the production power; it is necessary to use a lot of cooling water for cooling before the aluminum ingot is formed; during the cooling process, the large thermal energy of the aluminum liquid is released into the cooling water; hot water vapor occurs.
The casting machine bearing is in the high temperature water vapor environment; the bearing is a lot of grease smooth; the added smooth grease will be melted and overflowed due to the high temperature in a short time; the protection and protection is difficult; the equipment is also difficult to clean. Then there are steel layout bearings that are very easy to corrode and rust in hot and humid environment; the failure rate is very high; the equipment repair cost is high; the equipment operation is often confused by the following two problems.
It is difficult to complete the high-temperature continuous operation of the oil supply operation. The ingot, the ingot, the ingot, the ingot and other equipment of the casting machine are installed in the unit casing; each of the conversion bearings is marked with a nozzle device that is regularly written with smooth grease; Parking removes the casing; presses the grease with a grease gun. And the machine has more than 30 oil filling points; long-term operation protection can not complete this cumbersome oiling operation; it is only necessary to hold the oil bottle in the operation of the bearing Set of exterior; smooth oil is difficult to enter the conflicting side of the bearing; most bearings are in conflict.
The ambient temperature is high; the grease is smooth and not used to the molybdenum disulfide smooth grease used in the current casting machine rolling bearings. It is known as the high temperature grease; we know that its base oil is a petroleum product; plus a few high temperature resistant molybdenum disulfide increase agent; The temperature limit is also 120 ° C. It is estimated that the casting machine bearing operating temperature can reach 200 ° C; has far exceeded the smooth grease temperature limit.
Under such high temperature conditions; the base oil in the smooth grease will become thinner and gradually transpire; the remaining carbon residue, molybdenum disulfide and dust will be mixed into a solid block to condense on the support frame of the rolling bearing; not only the smoothing effect is lost; It also prevents the normal operation of the rolling bearing and wears out quickly; it can be stopped for up to 2 weeks; the bearing is removed to remove the new grease.
I. Wear situation The abnormal wear of the bearing caused by the two major problems in the bearing operation of the aluminum ingot casting equipment is more severe. Take the aluminum alloy ingot structure as an example; the bearing has a uniform service life of 2 months; when the wear is severe, it will actually be 5MM. The inner ring wears through; the equipment cannot continue to work.
The wear is uneven. The reason is that the original oil supply method can not be completed; the outside of the bearing in the operation has to be smelted with thin oil; a few can be leached into the bearing; the wear is more than 50% of the The shaft and sleeve are not smoothed; but in the case of dry conflicts, strong adhesive wear occurs. This wear quickly increases the gap between the shaft and the sleeve; the dust is more accessible; it constitutes a vicious circle.
Second, the choice of oil-free self-smooth bearing in order to deal with the high temperature, low speed, heavy load, dust, water shower and shock oscillating smooth problems in mechanical equipment; the choice of oil-free self-smooth bearings.
1. The layout of the bearing from the smooth bearing is to develop the appropriate holes in the metal collision surface of the bearing matrix; and embed the molybdenum disulfide, graphite and other composite self-lighting sliders embedded in the metal sleeve; Composite bearing; solid smoothing agent friction area of ​​25-65%. Solid self-lighting slider can work normally at 280 ° C high temperature. However, due to its low mechanical strength; load bearing ability is weak; easy to deform; it is embedded in metal The defect can be pressed in the hole groove; the metal is formed to bear some bearing effect; the smoothing effect from the light slider.
The smooth mechanism of this self-smooth bearing is in the process of the sliding conflict between the shaft and the sleeve; a part of the smooth material is transported to the metal appearance of the shaft; the small flat surface is filled; and a stable solid smoothness is formed. Membrane; constitutes a solid smooth film between the grinding; avoids the adhesion between the shaft and the sleeve. This rationality summarizes the complementary strengths of the copper alloy and the non-metal grinding data; uniquely suitable for oil-free, high temperature, high load Low speed; anti-fouling, anti-corrosion, moving range in strong radiation environment; and special working conditions under the condition that the water or other solution is moisturized and the bottom is unable to add smooth grease.
2. The area occupied by the self-lighting slider is related to the working speed and bearing strength of the self-lighting slider; the operating speed is low, the bearing strength is large; the area occupied by the metal should be larger. The area of ​​the traveling wheel bearing from the light slider is about 25%; the bearing of the pulling spindle is smooth and plentiful; the bearing strength is not large; the area occupied by the light slider is about 65%.
3, the technical requirements of the bushing material bushing should be made of alloy copper; the bushing should have a higher hardness; usually heat treatment; its hardness is not lower than HRC45.
4. Several shapes and inlay requirements of the self-lighting slider. The shape of the self-lighting slider has two kinds of cylindrical shape and rectangular shape; the self-smoothing can be selected from the cylindrical shape according to the size of the area; instead, a rectangular shape can be used. Inlaid and strong; to prevent falling in the work.
5. Cooperating gap value between bushing and shaft The linear expansion coefficient of the self-lighting slider is about 10 times that of steel. It is the change of custom bearing temperature; the gap between shaft and bushing is four-stage dynamic cooperation of original metal parts (D4/DC4) 0. 032 ~ 0. 15MM; increased to 0. 45 ~ 0. 5MM. From the light slider on the side of the conflict, the outstanding bushing metal 0. 2 ~ 0. 4MM. This will be abundant in the initial running-in period of the bearing operation Smooth; cut the cost of power drag power.
6, oil-free from the strength of the smooth bearing A, no oil smooth or less oil smooth; suitable for places that can not be refueled or difficult to refuel; can be used in the protection or less protection,
B, good wear resistance; conflict coefficient. lemon 倜ムC, excessive elastoplasticity; can spread the stress on a wider touch surface; improve the bearing capacity of the bearing,
D. Near the static motion conflict coefficient; can eliminate the flaw at low speed; then ensure the accuracy of the machine operation,
E. It can make machinery reduce oscillation, reduce noise, avoid pollution; improve working conditions,
F. It can form a carrying film during the operation; it can protect the shaft from grinding;
G. The hardness requirement of the grinding shaft is low; the unscheduled shaft can be used; then the processing difficulty of the associated parts is reduced.
H, thin wall layout, light weight; can reduce mechanical volume,
I. The bushing material is brass; it can be used in corrosive media.
After the theory of an aluminum company; the casting machine bearing changed to oil-free self-smooth bearing; it has been used for 15 months; and still working; the gap between the shaft and the bushing does not exceed 1MM; it is estimated that it can be used for another 12 months; Beyond the original life of the application (2 months).
Oil-free self-smooth bearings can not only be used well in aluminum ingot casting machines; they can be used together without oil, high temperature, high load, low speed; anti-fouling, anti-corrosion, moving radiation in strong radiation environment; and in water Or equipment under special working conditions where the solution is moisturized and the base cannot be smoothed; such bearings have a wide range of implementation values.
At present, most of the bearings used in various machinery industries are still balls, needles and the like; but some have chosen self-smooth bearings; trust will soon come from smooth bearings will become the dominant bearing. The following are some of the characteristics of self-smooth bearings. And advantages:
1, no oil smooth or less oil smooth; suitable for places that can not be refueled or difficult to refuel; can be used without protection or less protection,
2, good wear resistance; conflict coefficient. Lemon 倜ム3, excessive elastoplasticity; can spread the stress on a wider touch surface; improve the bearing capacity of the bearing,
4. Near the static motion conflict coefficient; can eliminate the flaw at low speed; then ensure the accuracy of the machine operation,
5, can make machinery reduce oscillation, reduce noise, avoid pollution; improve working conditions,
6. It can form a carrying film during the operation; it can protect the shaft from grinding;
7. The hardness requirement of the grinding shaft is low; the shaft that has not been tempered and treated can be used; then the processing difficulty of the associated parts is reduced.
8, thin wall layout, light weight; can reduce the mechanical volume,
9, the reverse side of the steel can be electroplated with a variety of metals; can be used in corrosive media, has been widely used in various mechanical sliding parts; for example: printing presses, textile machines, tobacco machinery, micro-motors, automobiles, motorcycles and agricultural and forestry machinery and many more.
Recommend to friends comments close window
Bearing related knowledge |
The method of manipulating the influence of bearing noise The layout of tapered roller bearing and the heat treatment agent quenching process of Guangyang bearing Analysis of the serious hazards of LM type linear bearing "pretending SKF bearing" |
This article links to http://
Please indicate China Bearing Network http://
Previous:Ball bearing Next:Circulating oil and bearing oil
LED grow lights are relatively new to the cannabis growing scene,but they have become wildly popular over the last few years with their ability to produce great yields while staying cool and using a reasonable amount of electricity.
Choose LED grow lights if...
You want to use the most cutting-edge indoor cannabis grow lights with a customized spectrum of light
You are willing to do some research to determine the best LED Grow Light for your space
You have some extra money to spend on your initial setup (some of the best LED grow lights are expensive!)
Quality (potency, smell, trichome development) is more important to you than yields/watt.
You don't want to deal with an exhaust system or ducting,and would prefer to just hang your grow light over your cannabis plants and let the lights cool themselves
Features
Deep penetration :Good lighting penetration,can penetrate to the deep of the plants
Modular Internal Build: Fully upgradable,easy warranties
Thermal Management:Custom copper core heatsinks quickly dissipates heat for cool operating temperatures
Powerful: 2nd Generation ultra penetration 5W LEDs light deep into the canopy
Versatile: Power cord available in 85~265V and international plugs
Lighter weight: Much lighter than the same products in the marketplace, safer for hanging .
Plants: Suitable for both vegetative phrase and flowering phrase
Product Images
The Plug you can choose
PAR Value of our 2000W LED Grow Lights
Applications
Our professional full spectrum COB LED Grow Light are suitable for all the indoor plants and good for seeding, growth,flowering and fruiting stages of plants, increasing the harvest and Saving energy.
Our Ageing Test
Package
Cautions:
1.Do not use the lights in dripping water or anywhere where they will get wet, water and electricity can be a dangerous mixture
2. The working environment for the light is -20~40 degree celsius,45%RH~90%RH.
3. To protect the light, Plz cut off the power when there is a lightning strike.
4. Don`t touch or move when the light working.
Suggestions:
1.Clean the dust inside every 6 months to ensure the good heat dissipation and long life time.
2.Don`t keep too short distance to the plant canopy to avert leaves bleaching.
3.Highly hang the lamp will weaken the energy and affect the growth cycle of the plants, so the lamp should not be hang too high.
4.While taking care of the plants, please spray the leaves and branches 2-3 times everyday, to ensure the plants do not wrinkle a wither, and have no phenomenon of few fruit, and hard pericarp.
Philizon have over 6 years' experience in designing and manufacturing led grow lights and LED Aquarium Light. Persuiting to offer the best LED grow lights for plants growth,we cooperate with the scientific research institutes and the Academies of Agricultural Sciences in USA, Australia Canada, UK and so on.A great number of commercial plant growers test the lights, and their feedbacks show that this lamp owns a lot of 640nm,660nm and 740nm lights, which gives the plants enough nutrient in the flowering and fruiting phase and bring a far higher yield than other led grow lights in the market.
Full Spectrum Grow Lights,Flowering Plant Grow Light,Flowering Led Grow Light,Grow Lights Full Spectrum
Shenzhen Phlizon Technology Co.,Ltd. , https://www.szledaquariumgrowlight.com