Epoxy epoxy anti-static floor how to maintain?
Presumably, we all know that epoxy anti-static floor paint has anti-static and anti-static long-lasting, long life, chemical resistance, smooth light, high mechanical properties and so on. Epoxy anti-static floor is a high-value, high-quality, high-demand product. Use the correct method to maintain the cleanliness and brightness of the ground. The specific methods are as follows:
one:
1. Epoxy anti-static floor should be maintained for 7-10 days after construction and it should be put into use. During this period, water or other solution should not be allowed to infiltrate the surface.
2. Every employee who enters the workshop must wear rubber-soled shoes
3, all hardware: such as iron chairs, iron tables and iron shelves, it must be their feet with soft plastic, rubber wrap or paper pad to avoid scratching the ground during use
4, the tractor pulls must fully lift the board off the ground, please pay special attention to the corner of the board when turning, do not scratch the ground
5, need to clean the ground when a good soft absorbent mop or wet or dry vacuum cleaner, can be cleaned with water or detergent
6, if the use of time is longer due to wear or scratch, a small area can be repaired, such as the larger area is recommended to re-roll once
7. Before the equipment enters the factory, lay a hard carton bottom on the floor to avoid scratching the ground during transportation.
8, carts, cart wheels please use hard or elastic rubber wheel, and plant inside and outside use separately
9, according to the requirements of the ground to do waxing (the effect can prevent scratching the ground)
two:
1. In the case of production-side construction, the construction environment should have sufficient isolation area to avoid the infiltration of ash, sand, etc. into the unbleached paint film epoxy floor.
2. The parts where the oil leaks frequently are often cleaned with sawdust so as not to denature the oil and absorb the ash layer, which becomes a stubborn stain. In areas with large areas of oil immersion, a wide cloth mop can be used to push sawdust to dry the oil on the floor.
3. The mechanic tools try to avoid falling ground.
4. If there is a large paint film breakage, repair it promptly so that the repair work can be carried out before the oil stain seeps into the foundation. When the workshop flushes the ground with water, avoid depositing the oil-water mixture in deep damage.
5. Contaminated areas, more prominent facades, corridors are cleaned 1-2 times a day with a wide cloth mop.
6. Coarse sand on the ground, mud should be cleaned in time to avoid sand grinding ground, reducing the wear on the ground.
7. Before the employees enter the clean area, they should change the soft-soled shoes; in the place where sand grains and mud are easily brought in, the entrance and exit can be provided with plastic blankets to facilitate the removal of shoe sole debris when the employees enter or leave the clean area.
8. When the forklift and forklift unload the cargo, pay attention to the cargo being laid flat to prevent the cargo side from picking up and dragging and scratching the ground.
9. Try to avoid braking when vehicles, forklifts, and forklifts are running.
Presumably, we all know that epoxy anti-static floor paint has anti-static and anti-static long-lasting, long life, chemical resistance, smooth light, high mechanical properties and so on. Epoxy anti-static floor is a high-value, high-quality, high-demand product. Use the correct method to maintain the cleanliness and brightness of the ground. The specific methods are as follows:
one:
1. Epoxy anti-static floor should be maintained for 7-10 days after construction and it should be put into use. During this period, water or other solution should not be allowed to infiltrate the surface.
2. Every employee who enters the workshop must wear rubber-soled shoes
3, all hardware: such as iron chairs, iron tables and iron shelves, it must be their feet with soft plastic, rubber wrap or paper pad to avoid scratching the ground during use
4, the tractor pulls must fully lift the board off the ground, please pay special attention to the corner of the board when turning, do not scratch the ground
5, need to clean the ground when a good soft absorbent mop or wet or dry vacuum cleaner, can be cleaned with water or detergent
6, if the use of time is longer due to wear or scratch, a small area can be repaired, such as the larger area is recommended to re-roll once
7. Before the equipment enters the factory, lay a hard carton bottom on the floor to avoid scratching the ground during transportation.
8, carts, cart wheels please use hard or elastic rubber wheel, and plant inside and outside use separately
9, according to the requirements of the ground to do waxing (the effect can prevent scratching the ground)
two:
1. In the case of production-side construction, the construction environment should have sufficient isolation area to avoid the infiltration of ash, sand, etc. into the unbleached paint film epoxy floor.
2. The parts where the oil leaks frequently are often cleaned with sawdust so as not to denature the oil and absorb the ash layer, which becomes a stubborn stain. In areas with large areas of oil immersion, a wide cloth mop can be used to push sawdust to dry the oil on the floor.
3. The mechanic tools try to avoid falling ground.
4. If there is a large paint film breakage, repair it promptly so that the repair work can be carried out before the oil stain seeps into the foundation. When the workshop flushes the ground with water, avoid depositing the oil-water mixture in deep damage.
5. Contaminated areas, more prominent facades, corridors are cleaned 1-2 times a day with a wide cloth mop.
6. Coarse sand on the ground, mud should be cleaned in time to avoid sand grinding ground, reducing the wear on the ground.
7. Before the employees enter the clean area, they should change the soft-soled shoes; in the place where sand grains and mud are easily brought in, the entrance and exit can be provided with plastic blankets to facilitate the removal of shoe sole debris when the employees enter or leave the clean area.
8. When the forklift and forklift unload the cargo, pay attention to the cargo being laid flat to prevent the cargo side from picking up and dragging and scratching the ground.
9. Try to avoid braking when vehicles, forklifts, and forklifts are running.
Stamping Parts,Metal Stamping Part,Local Steel Metal Stamping,Plate Parts
JIANGSU TONGDE INTERNATIONAL TRADE CO.LTD. , https://www.jstongdetrade.com