Innovation and Discussion on Routine Maintenance of Turnstiles

At present, various types of pedestrian walkway gates (three-roll gates, wing gates, swing gates, full-height rotation gates, and speed-through gates) on the market integrate mechanical, electronic, microprocessor control, and various read-write technologies organically. More and more people are welcome. Everybody can often see various types of pedestrian walkway gates (three-roller gates, wing gates, swing gates) on sites, factories, communities, fitness clubs, subways, stations, scenic spots, stadiums and other places. , full-height turnstiles, speed-through doors, like the innovative intelligent three-roll gates, innovation-pass smart wing gates, innovative pass-gates, etc. Then how do the pedestrian walkway gates (three-roll gates, wing gates, swing gates, full-height rotation gates, and speed-through gates) are maintained and maintained? Let's let innovation intelligent engineers guide everyone's knowledge in this area.


First of all, we must know that the maintenance of pedestrian gates (three-roll gates, wing gates, swing gates, full-height rotation gates, and speed-through gates) is of vital importance. Like automobiles, maintenance and maintenance are needed. The pedestrian gates (three roller gates) The maintenance and maintenance of wing gates, swing gates, swing gates, full-height rotation gates, and speed-through gates have a direct impact on the service life of the gates. Therefore, they are used for pedestrian gates (three-roll gates, wing gates, swing gates, full-height rotary gates, and speeds). Through the regular maintenance, not only must be done, but also do a good job according to requirements, many users rarely maintain or even do not maintain, and other machines only think of the manufacturers before they go bad, only to replace the parts. This is often due to small losses, usually there is no maintenance, a little bit of a problem, a long time will affect the use, so we must understand the importance of maintenance of the gate. Maintenance begins with the following aspects.




First, the external cleaning and maintenance of the general pedestrian walkway gate (three roller gate, wing gate, swing gate, full height rotary brake, speed through the door, sliding brake) are made of domestic stainless steel 304, it is recommended that once a week external cleaning.

1. Clean the surface of pedestrian gates (three roll gates, wing gates, swing gates, full height rotation gates, speed gates, panning gates): Clean dust on the surface with a soft cloth and polish the outside of the chassis with a soft cloth and talcum powder. , Conditional can be coated with rust-proof oil, just coated with rust-proof oil do not rub it by hand, so natural drying can be 3-5 hours or so hand contact, otherwise it will destroy the surface rust effect.

2. How to remove rust spots from pedestrian gates (three-roll gates, wing gates, swing gates, full-height rotation gates, speed-through gates, panning gates): gates have been used for a long time, especially when used outdoors. Some rust spots, remove rust spots with sandpaper and talcum powder can eliminate rust spots, wipe must be along the gate on the gate to draw the lines of processing (protect thick grain direction), otherwise it will affect the appearance.

3, if it is the appearance of spraying or painting chassis, use a soft cloth to wipe off the dust on the outside, if exposed scratches, use the same color paint to make up, but be careful not to wing, swing gate, speed through the door of the infrared pair The part of the shot was painted, or the brake was accidentally alarmed, causing unnecessary trouble.

Second, the movement of maintenance: movement is the heart of the machine, must be well maintained, it is recommended to maintain every three months, such as the use of high frequency places such as: large factories, schools, large entertainment venues, etc., it is recommended to check once in January.

1. Cut off the power and open the cover of the pedestrian walkway gate (three-roll gate, wing gate, swing gate, full-height rotation gate, speed-through gate, translating gate), clean the surface dust, clean the transmission part and add butter, wing Gates, swing gates, speed gates, pan gears and wheel slots should also be properly greased.

2. Check the fasteners and connecting rods for loosening and tighten them.

3. Check the wearing condition of the wearing parts. The positioning arm of the three-roll gate and the positioning plate have more than 3mm gap and replace them in time. The normal clearance (1-1.5mm),

4. Pay attention to the limit switches and limit plates of wing gates and swing gates. Do not adjust them in a timely manner to prevent mistakes caused by adjusting them too far or too close.

Third, the pedestrian gates (three roller gates, wing gates, swing gates, full-height gates, speed gates, panning gate) circuit power supply and other accessories maintenance 1, cut off the power supply, clean the surface dust. Be careful not to wash with water and prevent short circuits from occurring.

2. Check if the infrared installation position of the wing gate and swing gate is firm and whether the infrared position is aligned. If the infrared position is offset, an alarm will occur and the position needs to be adjusted accurately.

3, according to the previous use, to see if there is a problem in the circuit part, there is no problem, then check the circuit, power supply, wires, plug-ins are exposed or loose, to be bandaged, finishing, plug the plug, check for leakage, if the wire has Aging should be replaced.

4. Refer to the gate manual to check if the parameters of each department are normal and there are no aging electronic components. There are problems, we must contact the manufacturers, follow the steps, find the root cause of the problem, replace individual electronic components.


Fourth, the above maintenance must have someone special maintenance, especially the maintenance of the movement and the circuit part, through innovation and intelligent channel engineer professional training, full understanding of the strengths and weaknesses in order to work posts.


PVC Marbling Ceiling Tiles

Imitation the marble tiles,offer various marbling for interior decoration.

Used widely in wall decoration,background,ceiling,bedroom,kitchen,etc.

Environmently decoration materials with good quality and competitive price.

Feature

1. Fireproof

Pvc Marbling Ceiling Tiles is non-flammable and conforms to the national grade B1 standard (GB8624-2012 Grade B1).

2. Water-proofing and moisture-proofing

The product is allowed to long-term expose to moist environment.

3. Easy to install

PVC Marbling Ceiling Tiles is easy to cut, saw nail, stick. it has a smooth finish one side that can be taped and jointed ready for decoration including wallpapering, painting, texture coat and veneer, and a rougher side for tiling.

5. Environment

PVC Marbling Ceiling Tiles does not contain any organic solvents, formaldehyde, asbestos, oils or other toxic substances that can have a negative impact on the environment and waterways.


Specification size

1220mm*2440mm

Surface Finish

High UV coating

Thickness

1-9mm

Color

Customized colors

Hardness

3H-6H

Materials

PVC

Type

PVC Marbling Ceiling Tiles

Installation

Easy installation

Life Span

15 years

Place of original

China


PVC marble ceiling

pvc wall panel


PVC Marbling Ceiling Tiles

Uv Pvc Marbling Ceiling Tiles ,Laminated Bathroom Ceiling Tiles ,Marble Color Pvc Ceiling Tiles,Pvc Ceiling Tiles With Marble Texture

Shandong Kingmarble Decoration Materials Co.,Ltd , https://www.pvcmarblepanel.com